| Engine Dynamometer System |
| SuperFlow |
Chassis Dynamometers
Engine Dynamometers
Flowbenches |
| |
|
800 Series Chassis Dyno
High-performance 42" Chassis Dynamometer
The 42-inch roll two-wheel-drive AutoDyn chassis dyno is our
highest-capacity chassis dynamometer. It features 42-inch
(107 cm) diameter rolls for minimum tire deflection and
maximum contact patch size. Torque is measured with a
temperature-compensating load cell for precise torque and
power readings. You can place this chassis dyno above or
below ground for testing.
This 42-inch roll AutoDyn chassis dyno can run a variety of
built-in vehicle tests, including single-gear or all-gear
tests at wide open throttle. Controlled acceleration,
controlled deceleration, step, steady-state, aero load, and
drive cycle tests can be easily run with the included eddy
current power absorber module. The steady-state and drive
cycle tests can be performed at full or partial throttle
settings.
The SuperFlow Sensor box monitors and measures the data from
the AutoDyn chassis dynamometer and comes ready to run the
eddy current brake. You can add a variety of accessories to
our sensor box, including temperature measurement, pressure
measurement, and air/fuel monitoring.
Each AutoDyn chassis dyno is shipped with SuperFlow's
handheld controller, ignition sensor clip, optical
tachometer, and WinDyn™ software package. Eight hours of
training are included in the price*.
* Labor cost for training is included in system price.
Travel costs, travel time and expenses not included.
Features:
- Air-actuated roll lock
- Upgradeable to single or dual eddy current power
absorber(s)
- Upgradeable to all-wheel-drive
- Bi-directional test capability
- Stand-mounted data acquisition and control system with
four liquid crystal displays
- Two lambda sensor inputs (sensors not included)
- Six expansion bays (for optional thermocouple, pressure,
voltage input modules)
- Handheld system control and display unit
- Inductive ignition sensor clip with adjustable gain.
- Optical tachometer
- Real-time weather station (air temp, barometric pressure
and humidity)
- Pit kit included.
- WinDyn™ software package
- 16 hours of training**
- One-year warranty, including parts and labor***
* Vehicle should be tied down using appropriate tie-down straps
and anchors.
** Labor cost for training is included in system price. Travel
costs, travel time and expenses not included. Actual travel
expenses are billed upon completion of training. Inertia only
units receive eight hours of training.
*** Does not include travel cost, travel time, and expenses.
Specifications:
Speed Rating
...........................up to 200 MPH (320 km/h)
- Maximum Wheel Power
- Inertia test, Large-roll models
......... 1,500 hp (1118 kW)
- Peak power absorption
- Single eddy current
........................... 700 hp (521
kW)
- Large-roll dual eddy current
......... 1,400 hp (1043 kW)
- At 10 minutes duration (temperature
dependent)
- Single eddy current
........................... 350 hp (261
kW)
- Large-roll dual eddy current
.............. 700 hp (521 kW)
Control Accuracy
.................................. ± 0.1 mph (0,2
km/h)
- Maximum Axle Load
- Cradle-roll
model............................... 7,000
lb (3500 kg)
- Large-roll models
............................ 10,000 lb (4535
kg)
- Power requirements
- All models
..............................110-250 VAC,
15-8 amps
- Single eddy
current....................208-250 VAC, 20
amps
- Dual eddy current
......................208-250 VAC, 40 amps
- Shipping Weights
(approximate)
- 2WD Upgradeable inertia ................
6,300 lbs (2865 kg)
- 2WD Single eddy current.................
7,000 lbs (3180 kg)
- 2WD Dual eddy current
................... 7,600 lbs (3455 kg)
- AWD Upgradeable inertia ..............
12,600 lbs (5715 kg)
- AWD Single eddy current...............
13,300 lbs (6033 kg)
- AWD Dual eddy current .................
13,900 lbs (6304 kg)
Options:
|
 |
Above Ground
Ramp Kit
SuperFlow offers lightweight aluminum ramp kits for the
AutoDyn 11 and AutoDyn 30 chassis dynos. Kits include
heavy-duty aluminum ramps and extended platforms that
support the vehicle during testing. Because they are
light-weight these ramps work great for portable dyno
applications and they are easy to move in and out of place.
Ramps are perfect if you are unable to install your
SuperFlow chassis dyno in a pit or when shop space is
limited because they stack neatly out of the way when not in
use. Contact a SuperFlow Sales Engineer today to get the
correct ramp kit for your chassis dynamometer.
|
|
|
 |
4-post Hoists
SuperFlow offers several different 4-post hoists to fit any
needs and budget. Models are available with a walking
platform, safety rails and access ladders to make working on
vehicles easy and safe. SuperFlow also offers an economy
hoist that does not include the extra features listed above,
but still works great for loading vehicles on and off your
chassis dyno quickly and easily.
All lifts come with tie-down anchor points at the front and
rear of the platform to secure vehicles for testing. 4-post
hoists let you make performance upgrades anywhere on the
vehicle without having to move it from the dyno. Additional
benefits include oil changes, performance upgrades, brakes,
tire rotations, etc.
Contact a SuperFlow Sales Engineer today to learn more about
4-post hoists as well as other options for above ground
installation of your SuperFlow chassis dyno.
|
|
|
 |
AutoDyn Tie Down
Strap Kit
Standard tie-down strap kits include (4), 2in. by 15ft.
heavy duty straps with ratchets and (2), 2in. by 4ft.
web-sling straps with eyelet to eyelet ends. Cored in-floor
anchors are available separately.
|
|
|
 |
In-Floor Anchors
In-Floor AnchorsSuperFlow offers in-floor, compression style
anchors to outfit your shop with convenient, yet out of the
way tie down points. The 3.5in. anchors feature a chain
receiver that allows you to quickly attach the tie down
chain or remove it when not in use. The anchors have a
10,000 lb. (4,536kg) horizontal rating and a 500 lb. (227
kg) vertical rating. A cover plate is included to fill the
receiver hole when the anchors are not being used.
*Chain is not included because each installation varies |
|
|
 |
Optical Wheel
Tachometer
SuperFlow’s optical wheel tachometer reads wheel speed using
an infrared beam and reflective tape. It features a magnetic
base for secure mounting to any AutoDyn frame. The optical
tach is non-contact and works in many applications where
inductive pickups may not. Contact a SuperFlow Sales
Engineer today for more information on all of the options
available for SuperFlow chassis dynamometers. |
|
|
 |
Inductive Spark
Pick-Up Assembly
SuperFlow’s Inductive Spark Pick-Up Assembly features a
rugged housing that protects the device from tough shop
environments and allows it to provide years of service. With
user-adjustable sensitivity you’re able to dial in the
device exactly how you want it.
The spark pick-up includes one inductive clip. For wasted
spark ignition systems a second clip can be added. Contact
SuperFlow today for more information on this and other
options to get the most out of your SuperFlow chassis dyno.
|
|
|
 |
Pressure Sensor
Expansion Kits
The SuperFlow sensor box is easily upgradeable at any time.
Several pressure sensor expansion kits are available that
provide up to 10 additional pressures per expansion panel
for fluid or gas pressures. Monitor oil, manifold, fuel
system, air inlet, exhaust and auxiliary pressures. View all
of the data live in our WinDyn software and also save it for
easy post test graphing and analysis.
- Ranges
- Oil Pressure 150 psi
- Manifold Pressure: 200 in Hg
- Fuel Pressure: 150 psi
- Air Inlet Pressure ± 140 in. Hg
- Exhaust Pressure: ± 140 in. H2O
- Auxiliary Pressures also available
- Metal transducers (for hydrocarbon
pressures)
- PCB-mount transducers (for non-hydrocarbon
pressures)
- 0-5 psi
- 0-150 psi
- 0-150 psi
- Differential pressure transducers
- ± 5 psi
- ± 30 psi
- ± 100 psi
- Different ranges can be set by the
factory
- Remote systems available for high pressures
- Ranges
- 0-150 psi
- 0-300 psi
- 0-2,000 psi
- *Requires Analog Input Expansion Panel
|
|
|
 |
Temperature
Sensor Expansion Kits
Expand your sensor box with a 16-channel thermocouple panel
for Type K, Type J or Type T thermocouples. Monitor oil and
water temperatures live in our WinDyn software then save the
data for easy post test graphing and analysis. Monitoring
temperatures is critical to accurate and repeatable testing
so SuperFlow offers several kits to suit any needs and
budget. Panels accept pole or spade thermocouple plug ends.
Contact SuperFlow today for more information on Temperature
Expansion Panels for your SuperFlow chassis dynamometer. |
|
|
 |
Oil Dipstick
Temperature Probe
Oil Dip Stick sensorSuperFlow's oil dipstick temperature
probe plugs directly into the temperature expansion panel so
you can get accurate oil temperature readings with every
test. It includes a 10in. extension cable and features a
temperature range of -67° F to 1,200° F (-55° C to 704° C).
It is also available with an analog output to plug directly
into the interconnect panel or analog panel. This version
has a temperature range of -67° F to 257° F (-55° C to 125°
C). |
|
|
 |
Analog Input
Expansion Panel
SuperFlow offers 8-channel analog voltage input panels so
customers can easily integrate data from exhaust gas
analyzers, lambda sensors, O2 sensors, and other emissions
monitoring equipment with our WinDyn software. You can then
monitor the data live during each test, and also save it for
post test graphing and analysis to see the data graphed over
the entire run. The panels can be configured with any
combination of the following ranges:
- 0-1 V
- 0-5 V
- 0-10 V
- 0-20 V
- 0-30 V
|
|
|
|
Battery Voltage
Input Cable
SuperFlow’s Battery Voltage Input Cable allows you to
monitor battery voltage live in our WinDyn software with the
0-20 VDC input. *Requires analog input expansion panel.
|
|
|
 |
Air Flow
Measurement Turbines
SuperFlow offers 4in. (10.2cm), 6in. (15.2cm), and 9in.
(22.9 cm), air flow measurement turbines. They are available
on their own or in a kit that includes a ceiling adapter,
flexible hose and carburetor adapter. The turbines have CFM
ranges as follows:
- 4in: 4 – 150 CFM (2 – 70 lps)
- 6in: 10 – 800 CFM (5 – 380 lps)
- 9in: 20 – 1,200 CFM (9 – 560 lps)
Adapters are available to adapt the 9” (22.9cm) air turbine
to Holley and Dominator carburetors.
|
|
|
 |
Fuel Flow
Measurement Turbines
SuperFlow fuel turbines come in three different ranges:
- Low flow: 0.3 – 30 GPH (1.13 – 113 l/h)
- Standard flow: 6 – 60 GPH (22.7 – 227 l/h)
- High flow: 28 – 140 GPH (106 – 530 l/h)
|
|
|
 |
OBD-II Interface
Module
ODB-II Interface ModuleWith SuperFlow’s OBD-II Interface
Module you can easily monitor and record any OBD-II data
that the ECM makes available directly in our WinDyn
dynamometer software. The device plugs directly into the OBD-II
port and automatically shows you the available PIDs for that
vehicle. You can then quickly configure the system to
display the channels that you want to monitor live on
custom, user-defined WinDyn screens. With SuperFlow’s high
speed data acquisition you can close-loop control to OBD-II
channels and save any of them you want for post test
analysis and graphing.
With the OBD-II Interface Module you’re also able to read
Diagnostic Trouble Codes (DTC’s) and clear them once they
are resolved. Contact a SuperFlow Sales Engineer today for
more information on the OBD-II Interface Module for your
SuperFlow chassis dyno.
|
|
|
 |
Air/Fuel Sensor
Packages
Air/Fuel SensorSuperFlow offers several lambda packages for
measuring air/fuel ratios. These packages integrate with our
WinDyn dynamometer software for live monitoring and easy
post test graphing and analysis. Contact a SuperFlow Sales
Engineer today to learn more about the available options so
you can get the most out of your SuperFlow chassis dyno.
|
|
|
 |
Tailpipe
Air/Fuel Probes
Tailpipe Air Fuel ProbesWith SuperFlow exhaust probes you
can measure air/fuel data directly from the tailpipe.
Tailpipe probes integrate with our WinDyn dynamometer
software for live monitoring and easy post test graphing and
analysis. Contact a SuperFlow Sales Engineer today to learn
more about the available exhaust probes for your chassis
dynamometer.
|
|
|
 |
Diesel Exhaust
Opacity Meter
6500 Smoke AnalyzerSuperFlow’s Diesel Exhaust Opacity Meter
measures the opacity of visible smoke coming from the
exhaust. It’s rugged and portable design provides years of
easy use. Contact SuperFlow today for more information on
this and all the available options for your SuperFlow
chassis dyno.
|
|
|
 |
Volumetric
Blow-by Sensors
Blow-by SensorSuperFlow’s blow-by sensors measures the
volumetric flow of crankcase blow-by. Two sizes are
available: 0.4 to 16 ACFM and .25 to 10 ACFM. Users have the
option to choose either an analog or frequency output.
Contact a SuperFlow Sales Engineer today for more
information.
|
|
|
 |
Driver’s Trace
Software
Driver's Trace SoftwareSuperFlow’s Driver’s Trace Software
integrates seamlessly with your SuperFlow chassis
dynamometer and allows drivers to follow a real-time moving
driver’s trace on it’s easy-to-read display. It can run any
.csv based drive cycle and it is easy to configure. Special
operations like shift points or display messages for the
driver can be included in the trace so each test is accurate
and repeatable. Contact a SuperFlow Sales Engineer today for
more information on our Drivers Trace Software for you
chassis dynamometer.
*Requires WinDyn 2.7 or higher.
|
|
More Info:
 Downloads
|
Are you trying to inquire about a part
or check availability of a product or a solution service?
Please either call / WhatsApp (60) 19 333 9484 at or email us at
wso@assurich.com.my
or submit an enquiry form
online. |
|
